Today I managed a session in the workshop and completed (other than cutting a screwdriver slot in the valve faces) the first set of 8 valves. Last night I thought I would change my plan and get something to revolve to spur me on! To that end I ma going to get the valve side completed i.e. the camshaft fitted and working on one engine. To that end I drew up machining methods for the tappets, nuts, valve inserts, and camshaft bearings so that side of the engine works!
So after completing the valves the next items I was going to tackle was the two 1/4" hex nuts per valve. That was until I found I didn't have a suitable drill for the tapping. According to my charts I needed a 1.8mm No. 50 or 0.0709" drill. When going to my numbers drill box the only one missing is ............yep No. 50. So that job was put to one side and instead I decided to make the two camshaft bushes. The first went well enough and was reamed 0.250" and was pleased when it fits the camshaft nicely.
The second bush however produced another problem when checking the main block casting. This one was bought second and had some work done by the previous owner. All the work when checked previously was of a high standard, however the two holes bored previously were not the same. One, the timing end was spot on but the second was slightly oval! So worked stopped on the bush because it will need to be oversized, and the casting set up on my angle plate on the mill and the hole bored circular. When the finished 'round' hole was measured the bush will need to be some 35 thou oversize.
I can't see this will cause any problems yet, but will keep my fingers crossed. I will be using some hardening powder for both the nuts and the tappets, for the first time so that will be interesting. I have had it for a couple of years now and never used it before so if anyone has any tips additional to the 'normal' instructions I have, that would be very helpful.
-
-
Nice to see the 3/32″ reamed hole came out in the centre of the valve guide
-
-
Boring one end of the casting to be circular!
-
-
Timing end bush for camshaft
-
-
Current progress with 8 valves, 1 valve guide, & 1 camshaft bush
About Mike Freeman
Hello, my name is Mike Freeman and I am a retired Chief Fire Officer from the United Kingdom with a keen interest in model engineering, silver caddy spoons and sea fishing. I live in the pretty fishing port of Brixham, South Devon, in the United Kingdom.
I am a sufferer of degenerative osteoarthritis, which impacts on the amount of time I can spend in the workshop, and is the reason why you will see seats and a stool in some of the photo's. I have only recently added the above sentence after a discussion with one of my Doctor's from the excellent pain clinic, based in Torbay. This does affect concentration one of the reasons why I double then re-double my measurements and set ups.
Before completing nearly 30 years of public service I and my wife Sandy, owned and ran, a small restaurant in Okehampton Devon. Prior to marriage I worked for my father in his various businesses, in the early days these were garages, which he bought in a run down state, then built them up before moving on, to start again.
I took every opportunity in those early days, to work in his workshop's
learning 'on the job' rather than as an apprentice. This, I suspect, is the reason why my building various model's in the early days, turned into model engineering, when funds allowed the required equipment to be bought.
My workshop comprises one half of a detached double garage. It has a
stud wall separating the two halves and unusually perhaps, its own
shower/toilet/washbasin compartment! (the true reason for buying the
bungalow - don't tell the wife!!!)
It is fully insulated with a ceiling and fluorescent lighting supplementing the one window. Several double electrical sockets are dotted around in
relevant positions.
Equipment consists of 2 lathes (1 Myford ML 10 and 1 Chinese variable
speed motor with etched glass DRO's), 1 milling machine (RF25 far East) floor standing pillar drill, Proxxon bandsaw, Warco bandsaw, 6" wire brush and polishing mop motor, 6" coarse and fine grinder, Proxxon mini drill, various benches and an engineers vice. I have just acquired a third lathe, a Myford ML7 which I am at present evaluating so I can decide which of the Myford's I will keep.
I have only just bought the Chinese lathe and had it fitted with DRO's prior to delivery. And what a bonus they are! So good in fact that I decided to buy another set for the Milling machine. Whilst my engineering experience can only be described as limited, I find the use of DRO's has affected my accuracy levels which have improved tremendously (although that's not saying much!) and would recommend their fitting to any model engineer.
Prior to retirement I built for my son's 17th birthday a Locost car. This
was a tremendous project and a great feeling when it passed its test. The book it was based on suggests it can be built for £250. Ours was nothing special in the sense of all new parts but still cost about £900 to build!
