I had a short session of about 90 minutes in the workshop yesterday morning, carrying on with my 'secret' project.........before going sea fishing with my brother Steve and his son Adrian (see if your interested).
I have also managed a session this morning albeit brief, where progress did not go so well.... All this means that the cams and the continued work on the Fowler have again slipped. Its a good job I am not doing this for a living!
Hopefully tomorrow will see the 'secret' project come close to finishing (I wouldn't lay bets on it though!) so I can restart work on the rest of the work. And on that point to impose so discipline for the remainder of the year I decided (over a cup of tea) that the following items form the priorities until the first of January 2009.
1. Cams for the team build.
2. Dummy plate for the boiler on the Fowler
3. Tapping tool fixture/stand
4. Fixing the hornplates to the Fowler so she sits on her own four wheels
5. Die holder (sliding) for the tailstock of both lathes. I am really fed up with the tapping and thread cutting methods I use at the moment.
That should be more than enough to keep me busy till the end of the year.
About Mike Freeman
Hello, my name is Mike Freeman and I am a retired Chief Fire Officer from the United Kingdom with a keen interest in model engineering, silver caddy spoons and sea fishing. I live in the pretty fishing port of Brixham, South Devon, in the United Kingdom.
I am a sufferer of degenerative osteoarthritis, which impacts on the amount of time I can spend in the workshop, and is the reason why you will see seats and a stool in some of the photo's. I have only recently added the above sentence after a discussion with one of my Doctor's from the excellent pain clinic, based in Torbay. This does affect concentration one of the reasons why I double then re-double my measurements and set ups.
Before completing nearly 30 years of public service I and my wife Sandy, owned and ran, a small restaurant in Okehampton Devon. Prior to marriage I worked for my father in his various businesses, in the early days these were garages, which he bought in a run down state, then built them up before moving on, to start again.
I took every opportunity in those early days, to work in his workshop's
learning 'on the job' rather than as an apprentice. This, I suspect, is the reason why my building various model's in the early days, turned into model engineering, when funds allowed the required equipment to be bought.
My workshop comprises one half of a detached double garage. It has a
stud wall separating the two halves and unusually perhaps, its own
shower/toilet/washbasin compartment! (the true reason for buying the
bungalow - don't tell the wife!!!)
It is fully insulated with a ceiling and fluorescent lighting supplementing the one window. Several double electrical sockets are dotted around in
relevant positions.
Equipment consists of 2 lathes (1 Myford ML 10 and 1 Chinese variable
speed motor with etched glass DRO's), 1 milling machine (RF25 far East) floor standing pillar drill, Proxxon bandsaw, Warco bandsaw, 6" wire brush and polishing mop motor, 6" coarse and fine grinder, Proxxon mini drill, various benches and an engineers vice. I have just acquired a third lathe, a Myford ML7 which I am at present evaluating so I can decide which of the Myford's I will keep.
I have only just bought the Chinese lathe and had it fitted with DRO's prior to delivery. And what a bonus they are! So good in fact that I decided to buy another set for the Milling machine. Whilst my engineering experience can only be described as limited, I find the use of DRO's has affected my accuracy levels which have improved tremendously (although that's not saying much!) and would recommend their fitting to any model engineer.
Prior to retirement I built for my son's 17th birthday a Locost car. This
was a tremendous project and a great feeling when it passed its test. The book it was based on suggests it can be built for £250. Ours was nothing special in the sense of all new parts but still cost about £900 to build!
